Towel Rack & Plywood Quad Crash

Free PDF plans for towel rack & plywood quad crash and easy free woodworking projects. Discover thousands of images about towel rack & plywood quad crash. The best way to begin your hobby or small business in building furniture, woodworking and towel rack & plywood quad crash.

Woodworking Projects & Plans for "Towel Rack & Plywood Quad Crash":

Towel Rack & Plywood Quad Crash

Towel Rack & Plywood Quad Crash

Towel Rack & Plywood Quad Crash...

File0006

File0006

FILE0006...

450zx Walkaround And Reving.

450zx Walkaround And Reving.

Vh45de equipped 300zx with dry-sump oil system...

Rally Florida At Eastbay Raceway - Charlie Driving

Rally Florida At Eastbay Raceway - Charlie Driving

Charlie Thompson driving the Legacy at the Florida Rally event on Nov 17, 2013...

Flying Around The Park With The Quad

Flying Around The Park With The Quad

Flying around the park with the quad...

Team Black Sheep Racing

Team Black Sheep Racing

Time Lapse video of 24 Hours of Lemons South at CMP...

Quadcopter Maiden Flight

Quadcopter Maiden Flight

This is the maiden flight of scratch built, low cost quadcopter. Frame made from Home Depot.625" sq towel bars and Michaels.125" thk plywood. Will post plans if there is interest.- RC Timer BC-2826/13 1000KV motors, on ebay- RC Timer 30A ESC, on bay- 10x4.5" EPP1045 CW + CCW Counter R...

First Tricopter Video

First Tricopter Video

First successful flight of my tricopter with a camera attached. All the cool stuff happened after it stopped recording! Definitely have some vibration issues to take care of...

450zx Engine Pull Timelapse

450zx Engine Pull Timelapse

I had to pull the engine out of my Z due to rod knock. I decided to play with the GoPro a bit and do a timelapse of the pull and teardown. Some of the boring parts have been cut. Number 3 rod bearing was almost completely gone. Crank is toast. Need to figure out why some of the wrist pins are tight...

File0002

File0002

FILE0002...

Stinky's Z Fest 2013 Driver's Challenge Run

Stinky's Z Fest 2013 Driver's Challenge Run

Having a great time at the Z Fest Driver's Challenge event in Tavares, Fl. It's a tight little course but lots of fun. Driving my 88 300zx with a vh45 motor swap, Stance coilovers, and a j30 rear subframe swap...

H-quad Ver. 2 With Aluminum Arms

H-quad Ver. 2 With Aluminum Arms

The first H-Quad was made with all wood but too heavy, so I deceided to go with 3/16 plywood with foam sandwiched between top and bottom, and 15 inch arms made with towel rack from Home lighter and flys really good. Flight controller is a cheap Free Flight Controller from China. If it flys this well...

Xcopter Scratch Built With A Hk I86 Controller

Xcopter Scratch Built With A Hk I86 Controller

After figuring out how to arm this board in the X mode, I found that the HK i86 controller with MEMs 3 axis gyro, is Much more stable than the HK V2. To arm the board with a DX6i mode 2, after stick centering and throttle range setting, one must go down and left on the right stick to arm. Up and rig...

Nissan Consult Drifting Lights

Nissan Consult Drifting Lights

RGB LED controller that connects to a Nissan Consult diagnostic port. The lights are programmed to change color based on parameters pulled from the ecu. It's currently running on RPM but will also run on throttle position, speed, air flow meter voltage, or any other parameter the ecu will output thr...

450 Plywood Wonder Quad

450 Plywood Wonder Quad

450 plywood frame, unknown tower hobby bell motors, 7 inch 3 blade props, 12 amp esc's. KK 2.0 just something I tossed together. Flies ok. Ebay special. I had KK 2.0 and Esc's The whole thing was under a hundred bucks...

Rally Florida At Eastbay Raceway - Jared Driving

Rally Florida At Eastbay Raceway - Jared Driving

Jared Rivers driving the Legacy at the Florida Rally event on Nov 17, 2013...

Tcopter Tricopter At Night With Leds

Tcopter Tricopter At Night With Leds

I did a maiden earlier that day and liked it so much, I painted it black and put LEDs on it. It has the i86 board on it from HobbyKing, 3 very inexpensive 1534kv motors from HobbyKing, a 9g HXT servo, two 24" towel bars and some 1/8" hobby plywood. This is a very inexpensive build and flie...

Plywood Mini Quad Acro Test Flight

Plywood Mini Quad Acro Test Flight

Plywood mini quad acro test flight...

First Test Flight Of My Aeroquad Prototype - Complete Video Tutorial Of Construction To Follow

First Test Flight Of My Aeroquad Prototype - Complete Video Tutorial Of Construction To Follow

Hello all, Here is my first test flight of my Aeroquad prototype, which was made from parts you can get at Home Depot. It's made from PVC, aluminum angle bracket, 1/8"plywood, nuts and bolts.I am putting together a complete Video Tutorial of the construction from beginning concepts to the final...